Home / Civil Engineering / UPSC Civil Service Exam Questions :: Section 12

Civil Engineering :: UPSC Civil Service Exam Questions

  1. Consider the following assumptions :
    1. Failure occurs on a plane surface.
    2. Wall is smooth but not necessarily vertical.
    3. Failure wedge is a rigid body.
    Coulomb's theory of earth pressure is based on assumptions

  2. A.
    1, 2 and 3
    B.
    1 and 3
    C.
    1 and 2
    D.
    2 and 3

    View Answer

    Workspace

    Discuss Discuss in Forum


  3. A 2-metre diameter water pipe is required to withstand a 200 meter head of water. Assuming the limiting tensile stress for the pipe material to be 200 kg/cm2, the minimum thickness of the material of the pipe to be used will have to be

  4. A.
    5 cm
    B.
    10 cm
    C.
    15 cm
    D.
    20 cm

    View Answer

    Workspace

    Discuss Discuss in Forum


  5. In the preliminary treatment of wastewater, skimming tanks are often included in the treatment scheme. Various features of skimming tanks are that these :
    1. can remove general floating matter.
    2. can remove oily and greasy matter.
    3. have detention time of 30 min.
    4. employ compressed air blown through diffusers.
    Which of these statements are correct ?

  6. A.
    1 and 3
    B.
    2 and 4
    C.
    2 and 3
    D.
    1 and 2

    View Answer

    Workspace

    Discuss Discuss in Forum


  7. Consider the following statements :
    1. A dummy activity is artificially introduced in a network when necessary.
    2. A dummy activity consumes some time.
    3. A dummy activity is represented by a dotted arrow.
    4. A dummy activity must necessarily be introduced in every network. Which of the above statements are correct ?

  8. A.
    1, 2 and 3
    B.
    1 and 3
    C.
    2, 3 and 4
    D.
    1 and 2

    View Answer

    Workspace

    Discuss Discuss in Forum


  9. Consider the following stages in the manufacturing of bricks :
    1. Weathering
    2. Moulding
    3. Tempering
    The correct sequence of these stages in the manufacturing of the bricks, is

  10. A.
    1, 2, 3
    B.
    2, 3, 1
    C.
    1, 3, 2
    D.
    3, 2, 1

    View Answer

    Workspace

    Discuss Discuss in Forum


  11. What is the predominating coagulation mechanism for raw water having high turbidity and high alkalinity?

  12. A.
    Ionic layer compression
    B.
    Adsorption and charge neutralization
    C.
    Sweep coagulation
    D.
    Inter particle bridging

    View Answer

    Workspace

    Discuss Discuss in Forum


  13. The momentum correction factor (β) is used to account for

  14. A.
    change in the direction of flow
    B.
    change in total energy
    C.
    change in mass rate of flow
    D.
    non-uniform distribution of vel-ocities

    View Answer

    Workspace

    Discuss Discuss in Forum


  15. Where is d'Alembert's principle employed ?

  16. A.
    In the design of long columns
    B.
    To determine stresses induced in thick cylinders
    C.
    To reduce a problem of kinetics to an equivalent problem of statics
    D.
    In the analysis of many geotechnical problems

    View Answer

    Workspace

    Discuss Discuss in Forum


  17. The hoop stress in a dome subjected to uniformly distributed load

  18. A.
    is always compressive
    B.
    is tensile at sections whose radius vectors are at angles less than 51°51' with the vertical
    C.
    is tensile at sections whose radius vectors are at angles greater than 51°51' with the vertical
    D.
    is always tensile

    View Answer

    Workspace

    Discuss Discuss in Forum


  19. A commonly used handpump is the

  20. A.
    centrifugal pump
    B.
    reciprocating pump
    C.
    rotary pump
    D.
    axial flow pump

    View Answer

    Workspace

    Discuss Discuss in Forum