Home / ECE / Exam Questions Paper :: Section 14

ECE :: Exam Questions Paper

  1. The full form of the abbreviations TTL and CMOS in reference to logic families are

  2. A.
    Triple Transistor Logic and Chip Metal Oxide Semiconductor
    B.
    Tristate Transistor Logic and Chip Metal Oxide Semiconductor
    C.
    Transistor Transistor logic and Complementary Metal Oxide Semiconductor
    D.
    Trisate Transistor Logic and Complementary Metal Oxide Silicon

    View Answer

    Workspace

    Discuss Discuss in Forum


  3. In which one of the following types of analog to digital converts the conversion time is practically independent of the amplitude of the analog signal?

  4. A.
    The dual slope integrating type
    B.
    Successive approximation type
    C.
    Counter ramp type
    D.
    Tracking type

    View Answer

    Workspace

    Discuss Discuss in Forum


  5. The constraint on r = |z| for which the following non-causal system converges is

  6. A.
    |z| < 1/4
    B.
    |z| < 1/2
    C.
    |z| < 4
    D.
    |z| < 2

    View Answer

    Workspace

    Discuss Discuss in Forum


  7. Consider the following statements:
    The conductivity of a metal has negative temperature coefficient since:

    1. The electron concentration increases with temperature.
    2. The electron mobility decreases with temperature.
    3. The electron-lattice scattering rate increases with temperature.
    Which of the above statements is/are correct?

  8. A.
    1 only
    B.
    1 and 2
    C.
    2 and 3
    D.
    3 only

    View Answer

    Workspace

    Discuss Discuss in Forum


  9. The Table given below is the mark obtained by 2 students in 8 different subjects.

    The regression line of y on x is:

  10. A.
    y + 0.57x = 9.7558
    B.
    y - 0.57x = 9.758
    C.
    033y + x = 6.335
    D.
    0.33y - x = 6.335

    View Answer

    Workspace

    Discuss Discuss in Forum


  11. The Ebers-Moll equation for IE in CB configuration is given by

  12. A.
    IE = anICIECO
    B.
    IE = a1Ic + ICO
    C.
    D.

    View Answer

    Workspace

    Discuss Discuss in Forum


  13. The transfer function of a controller is given as Kp + Kd.s + where Kp, Kd and Ki are constants. What type of controller is this?

  14. A.
    Proportional
    B.
    Proportional plus derivative
    C.
    Proportional plus integral
    D.
    Proportional plus integral plus derivative

    View Answer

    Workspace

    Discuss Discuss in Forum


  15. Consider the following statements about a good power supply:

    1. The a.c. ripple should be high
    2. Sv, (Voltage stability factor) should be low
    3. ST, (Temperature stability factor) should be low
    Which of the above statements are correct?

  16. A.
    1, 2 and 3
    B.
    2 only
    C.
    3 only
    D.
    2 and 3 only

    View Answer

    Workspace

    Discuss Discuss in Forum


  17. Which one of the following statements is correct for MOSFETS?

  18. A.
    p channel MOS is easier to produce than n channel MOS
    B.
    n channel MOS must have twice the area of p channel MOS for the same ON resistance
    C.
    p channel MOS has faster switching action than n channel MOS
    D.
    p channel MOS has higher packing density than n channel MOS

    View Answer

    Workspace

    Discuss Discuss in Forum


  19. Which of the following transducers requires a high input impedance preamplifier for proper measurements?

  20. A.
    Thermocouple
    B.
    Piezoelectric
    C.
    Thermistor
    D.
    L.V.D.T

    View Answer

    Workspace

    Discuss Discuss in Forum