Home / Mechanical Engineering / Manufacturing and Production Technology :: section-1

Mechanical Engineering :: Manufacturing and Production Technology

  1. Work speed of circular electrode of 220 mm diameter for carrying out seam welding at 4 welds per cm on 1.6 mm thick mild steel tube. Welding cycle consists of 3 cycles ‘on’ and 2 cycles ‘off’ Power supply is at 50 Hz. Calculate R.P.M. and energy requirement of the above circular electrodes assuming effective resistance between electrodes as 100 ohm.

  2. A.

     2.17 rpm, 600 joules

    B.

     6.8 rpm, 6 joules

    C.

     5.03 rpm, 600 joules

    D.

     22 rpm, 600 joules

    View Answer

    Workspace

    Discuss Discuss in Forum


  3. Internal gears can be made by

  4. A.

     Hobbing

    B.

     Shaping with pinion cutter

    C.

     Shaping with rack cutter

    D.

     Milling

    View Answer

    Workspace

    Discuss Discuss in Forum


  5. What is the type of welding defect caused due to poor manipulation of weld rod or a dirty joint called?

  6. A.

     Porosity

    B.

     Undercut

    C.

     Under fill

    D.

     Crack

    View Answer

    Workspace

    Discuss Discuss in Forum


  7. The broaching operation in which the work moves past the stationary tool is called

  8. A.

     Pull broaching

    B.

     Push broaching

    C.

     Surface broaching

    D.

     Continuous broaching

    View Answer

    Workspace

    Discuss Discuss in Forum


  9. The cutting speed for drilling __________ with high speed steel drills is 24 to 45 m/min.

  10. A.

     Mild steel

    B.

     Copper

    C.

     Aluminium

    D.

     Brass

    View Answer

    Workspace

    Discuss Discuss in Forum


  11. Trepanning is an operation of

  12. A.

     Making a cone-shaped enlargement of the end of a hole

    B.

     Smoothing and squaring the surface around a hole

    C.

     Sizing and finishing a small diameter hole

    D.

     Producing a hole by removing metal along the circumference of a hollow cutting tool

    View Answer

    Workspace

    Discuss Discuss in Forum


  13. Lapping is an operation of

  14. A.

     Making a cone-shaped enlargement of the end of a hole

    B.

     Smoothing and squaring the surface around a hole

    C.

     Sizing and finishing a small diameter hole

    D.

     Producing a hole by removing metal along the circumference of a hollow cutting tool

    View Answer

    Workspace

    Discuss Discuss in Forum


  15. The saw milling is an operation of

  16. A.

     Producing grooves around the periphery of a cylindrical or conical workpiece

    B.

     Producing narrow slots or grooves on a workpiece

    C.

     Reproduction of an outline of a template on a workpiece

    D.

     Machining several surfaces of a workpiece simultaneously

    View Answer

    Workspace

    Discuss Discuss in Forum


  17. The chamfering is an operation of

  18. A.

     Beveling the extreme end of a workpiece

    B.

     Embossing a diamond shaped pattern on the surface of a workpiece

    C.

     Reducing the diameter of a workpiece over a very narrow surface

    D.

     Enlarging the end of a hole cylindrically

    View Answer

    Workspace

    Discuss Discuss in Forum


  19. The grooving is an operation of

  20. A.

     Beveling the extreme end of a workpiece

    B.

     Embossing a diamond shaped pattern on the surface of a workpiece

    C.

     Reducing the diameter of a workpiece over a very narrow surface

    D.

     Enlarging the end of a hole cylindrically

    View Answer

    Workspace

    Discuss Discuss in Forum