Home / ECE / Microwave Communication :: Section 5

ECE :: Microwave Communication

  1. A microwave connector should have high SWR.

  2. A.
    True
    B.
    False

    View Answer

    Workspace

    Discuss Discuss in Forum


  3. Assertion (A): A small section of high impedance line is equivalent to a series inductance.

    Reason (R): A small section of a low impedance line is equivalent to a series resistance.

  4. A.
    Both A and R are correct and R is correct explanation of A
    B.
    Both A and R are correct but R is not correct explanation of A
    C.
    A is correct but R is wrong
    D.
    A is wrong but R is correct

    View Answer

    Workspace

    Discuss Discuss in Forum


  5. Assertion (A): Bolometer is frequently used in microwave power measurement.

    Reason (R): In a bolometer the input microwave power causes a change in resistance.

  6. A.
    Both A and R are correct and R is correct explanation of A
    B.
    Both A and R are correct but R is not correct explanation of A
    C.
    A is correct but R is wrong
    D.
    A is wrong but R is correct

    View Answer

    Workspace

    Discuss Discuss in Forum


  7. The radiation resistance of a doublet antenna of length dl is proportional to

  8. A.
    δ l
    B.
    l)2
    C.
    l)3
    D.
    l)05

    View Answer

    Workspace

    Discuss Discuss in Forum


  9. Which of the following statements is not correct regarding modes of electromagnetic energy transmission?

  10. A.
    In TE mode the direction of electric field is always and everywhere transverse to the direction of propagation
    B.
    In TM mode the magnetic field pattern is always and everywhere transverse to the direction of propagation
    C.
    The subscripts is TE and TM designations denote the number of half sine wave variations of the field components in x and y directions respectively.
    D.
    TM11 is called the dominant mode.

    View Answer

    Workspace

    Discuss Discuss in Forum


  11. Oscillations are obtained from a reflex klystron only for combinations of anode voltage and repeller voltage that give a favourable transit time.

  12. A.
    True
    B.
    False

    View Answer

    Workspace

    Discuss Discuss in Forum


  13. In the given figure shows a 10dB directional coupler. If power input at port 1 is 100 mW, power output at port 3 is

  14. A.
    10 mW
    B.
    15 mW
    C.
    20 mW
    D.
    25 mW

    View Answer

    Workspace

    Discuss Discuss in Forum


  15. The noise figure of klystron amplifier is about

  16. A.
    25 dB
    B.
    3 dB
    C.
    zero
    D.
    1 dB

    View Answer

    Workspace

    Discuss Discuss in Forum


  17. Which one of the following is true for EM wave propagation through rectangular waveguide of cross-section 2a x a

  18. A.
    critical wavelength for TE10 mode is the same as that for TE02 mode
    B.
    critical wavelength for TE10 mode is one half of that for TE10 mode
    C.
    critical wavelength for TE10 mode is the same as that for TM10 mode
    D.
    critical wavelength for TE10 mode is double that for TE01mode

    View Answer

    Workspace

    Discuss Discuss in Forum


  19. In the given figure the line voltage after a number of reflections will be

  20. A.
    30 V
    B.
    -30 V
    C.
    10 V
    D.
    -10 V

    View Answer

    Workspace

    Discuss Discuss in Forum