Home / Computer Science / Computer Networking :: Managing a Cisco Internetwork

Computer Science :: Computer Networking

  1. Which command displays the configuration register setting?

  2. A.

     show ip route

    B.

     show boot version

    C.

     show version

    D.

     show flash

    View Answer

    Workspace

    Discuss Discuss in Forum


  3. What should the configuration register value be after you successfully complete the password recovery procedure and return the router to normal operation?

  4. A.

     0x2100

    B.

     0x2101

    C.

     0x2102

    D.

     0x2142

    View Answer

    Workspace

    Discuss Discuss in Forum


  5. You telnet into a remote device and type debug ip rip, but no output from the debug command is seen. What could the problem be?

  6. A.

     You must type the show ip rip command first.

    B.

     IP addressing on the network is incorrect.

    C.

     You must use the terminal monitor command.

    D.

     Debug output is sent only to the console.

    View Answer

    Workspace

    Discuss Discuss in Forum


  7. What does the command o/r 0x2142 provide?

  8. A.

     It is used to restart the router.

    B.

     It is used to bypass the configuration in NVRAM.

    C.

     It is used to enter ROM Monitor mode.

    D.

     It is used to view the lost password.

    View Answer

    Workspace

    Discuss Discuss in Forum


  9. You save the configuration on a router with the copy running-config startup-config command and reboot the router. The router, however, comes up with a blank configuration. What can the problem be?

  10. A.

     You didn

    B.

     NVRAM is corrupted.

    C.

     The configuration register setting is incorrect.

    D.

     The newly upgraded IOS is not compatible with the hardware of the router.

    View Answer

    Workspace

    Discuss Discuss in Forum


  11. The corporate office sends you a new router to connect, but upon connecting the console cable, you see that there is already a configuration on the router. What should be done before a new configuration is entered in the router?

  12. A.

     RAM should be erased and the router restarted.

    B.

     Flash should be erased and the router restarted.

    C.

     NVRAM should be erased and the router restarted.

    D.

     The new configuration should be entered and saved.

    View Answer

    Workspace

    Discuss Discuss in Forum


  13. Which command will show you the IOS version running on your router?

  14. A.

     sh IOS

    B.

     sh flash

    C.

     sh version

    D.

     sh running-config

    View Answer

    Workspace

    Discuss Discuss in Forum


  15. You need to gather the IP address of a remote switch that is located in Hawaii. What can you do to find the address?

  16. A.

     Issue the show ip arp command on the router connected to the switch.

    B.

     Issue the show ip route command on the router connected to the switch.

    C.

     Issue the show cdp neighbor command on the router connected to the switch.

    D.

     Issue the show cdp neighbors detail command on the router connected to the switch.

    View Answer

    Workspace

    Discuss Discuss in Forum


  17. A network administrator wants to upgrade the IOS of a router without removing the image currently installed. What command will display the amount of memory consumed by the current IOS image and indicate whether there is enough room available to hold both the current and new images?

  18. A.

     show version

    B.

     show flash

    C.

     show memory

    D.

     show buffers

    View Answer

    Workspace

    Discuss Discuss in Forum


  19. You copy a configuration from a network host to a router's RAM. The configuration looks correct, yet it is not working at all. What could the problem be?

  20. A.

     You copied the wrong configuration into RAM.

    B.

     You copied the configuration into flash memory instead.

    C.

     The copy did not override the shutdown command in running-config.

    D.

     The IOS became corrupted after the copy command was initiated.

    View Answer

    Workspace

    Discuss Discuss in Forum